-
-
The ready-to-use tribological composition is designed to process the hydraulic systems of trucks and special equipment in order to restore performance and extend the life.
Designed for 45liters of hydraulic oil in the lubrication system.
Recommended price: 2990 rub.
Item: 7ND1724
Volume: 100 ml.
Composition: nanostructure antiwear anti-friction repair and recovery composition NEODRIVE.
Properties:
• anti-friction (reduction of friction losses)
• antiwear (reduced wear rate)
• anti-seize (increase in ultimate load of setting friction surfaces)
The tribological composition of HYDRAULIC forms a protective servo-like film on the friction surface. The film has high wear resistance and a low coefficient of friction. It compensates for the wear of the material on the surfaces of the parts, reduces their roughness and, at the same time, keeps the lubricant on the friction surface, thereby providing more comfortable working conditions for the parts of the friction unit, which leads to an increase in the service life. It is important that the resulting nanomodified film is stable, and its positive effect on the state of rubbing parts during operation only grows over time and persists when changing the oil.
The tribotechnical composition does not affect the characteristics and condition of parts made of composite materials, ceramics, and rubber products.
Compatible with all hydraulic oils used in vehicle hydraulics, does not enter into chemical reactions with oil, does not change the viscosity of the oil.
The tribotechnical composition of NEODRIVE is not an oil additive.
Efficiency:
• Reduces friction and wear on rubbing surfaces
• Restores the parameters of worn-out units and mechanisms without disassembling them
• Optimizes gaps in friction pairs
• Holds oil on the surface of parts
• Restores hydraulic pressure to nominal values
• Restores tightness of stuffing box seal actuators
• Increases a resource of hydraulics in 1,5-3 times
• Accelerates the break-in process of the hydraulic system
• Reduces noise and vibration
• Increases oil life by 1.5-3 times
• Increases system pressure
The sequence of application of the tribotechnical composition "HYDRAULICS":
1. Warm up the car engine to a working temperature of at least +50 g.
2. Turn the hydraulic system off.
3. Pour the required amount of the composition into the hydraulic oil through the filling device at the rate of 10 ml of the composition per 9 liters of hydraulic oil.
4. After making tribological composition, it is necessary to immediately begin the operation of the hydraulic system and operate in normal mode for at least 30 minutes.
Note:
• It is allowed to use the composition in a constructive combination of a hydraulic system and a power steering.
• It is recommended to use the HYDRAULIC compound after every change of hydraulic oil.
Packaging:
50 ml bottle with cap and label.
Cardboard box with instructions for use.
Storage conditions: from - 20 to + 50 degrees.
Shelf life: 5 years. The date of manufacture is indicated on the label.
-
-
The ready-to-use tribotechnical composition is intended for processing the fuel system of internal combustion engines (gasoline, diesel) trucks and special equipment.
Designed for 2500-3000km of the vehicle.
Recommended price: 2990 rub.
Reference: 7ND1723
Volume: 50 ml.
Composition: nanostructure antiwear anti-friction repair and recovery composition NEODRIVE.
It is calculated on 2500-3000 km of run. It is recommended to carry out initial processing of the fuel system.
Properties:
• The tribotechnical composition of NEODRIVE is not a fuel additive, compatible with all types of fuel used in the car.
• The tribotechnical composition forms a servo layer on the details of the fuel supply system (including the supply system to the nozzles, especially piezoelectric nozzles), thereby protecting it from premature wear, and in some cases, restores worn areas of rubbing parts.
• The composition changes the molecular structure of the fuel so that the combustion process proceeds more fully, with an increase in heat transfer. Covers the surface of the combustion chamber with a layer of molecules that create the effect of repulsion of particles of burning fuel having the same charge. As a result, there is no soot on candles, nozzles, in the combustion chamber, rings, lower specific fuel consumption, lower coolant temperature, lack of self-ignition, reduction of detonation in gasoline engines, and mild operation of diesel engines.
Efficiency:
• reduces fuel consumption;
• reduces harmful exhaust emissions;
• restores and keeps clean injectors;
• improves engine performance;
• increases engine life;
• removes deposits on valves and in the combustion chamber;
• cleans the fuel system (jets, fuel pumps, nozzles, combustion chambers, candles);
• restores the rubbing surfaces of cams;
• increases throttle response;
• efficiency after 5-10 km of run.
The sequence of application of the tribotechnical composition "FUEL SYSTEM":
1. Processing is performed at an engine operating temperature of at least +50 degrees
2. Pour the contents of the bottle (50 ml) into the neck of the fuel tank at the rate of 1 bottle per 100 liters of fuel (gasoline, diesel fuel).
3. Immediately after filling the nanomodifier, the vehicle should start moving (at least 25-30 minutes).
Note: the following fuel system treatment is recommended after 2500-3000 km.
Packaging:
50 ml bottle with cap and label.
Cardboard box with instructions for use.
Storage conditions: from - 20 to + 50 degrees.
Shelf life: 5 years. The date of manufacture is indicated on the label.