For motor vehicles "ENGINE"
-
-
The ready-to-use tribotechnical composition is intended for processing the fuel system of internal combustion engines (gasoline, diesel) cars, four-stroke engines of motorcycles, jet skis, ATVs, snowmobiles, boats, motor boats and other equipment.
Designed for 2000-2500km mileage.
Recommended price: 1290 rub.
Reference: 7ND1718
Volume: 25 ml.
Composition: nanostructure antiwear anti-friction repair and recovery composition NEODRIVE.
Properties:
• anti-friction (reduction of friction losses)
• anti-wear (reduced wear rate)
• anti-seize (increase in ultimate load of setting friction surfaces)
Compatible with all motor oils, does not enter into chemical reactions with oils and additives, does not change the viscosity of oils.
The tribotechnical composition of NEODRIVE is not an oil additive.
Efficiency:
• Reduces friction and wear on rubbing surfaces
• Increases engine service life …………………… 2-3 times
• Increases the overhaul life ... 1,5-3 times
• Increases engine power ……………………… 15-18%
• Reduces fuel consumption ………………………………… 15-18%
• Increases and evens out compression in engine cylinders to rated values
• Restores the parameters of worn-out units and mechanisms without disassembling them
• Reduces exhaust gas toxicity by 70-80%
• Increases oil service life by 2-3 times
• Facilitates engine starting at low temperatures
• Eliminates wear during cold start
• Cleans the engine lubrication system of soot and tar deposits
• The cost of processing components and mechanisms is 2-3 times lower than the cost of repairs using conventional technologies
The sequence of application of the tribotechnical composition "ENGINE":
1. Warm up the engine to a working temperature of at least +50 g.
2. Stop the engine.
3. Pour the contents of the vial (50 ml) into the oil filler neck of the engine.
4. Let the engine idle for 5-10 minutes.
5. Make 5-7 relapses.
6. Stop the engine for 10 minutes.
7. Start the engine again and ensure a mileage of at least 50 km.
Note:
• If the oil is very dirty, treat the engine after changing the oil and oil filter.
• The engine can be treated both in old oil (if there is at least 1000 km of run before the next scheduled oil change), and during a scheduled oil change.
• Processing of the motor-vehicle engine with the ENGINE composition is carried out after each regular oil change.
Packaging:
50 ml bottle with cap and label.
Cardboard box with instructions for use.
Storage conditions: from - 20 to + 50 degrees.
Shelf life: 5 years. The date of manufacture is indicated on the label.
Properties:
• anti-friction (reduction of friction losses)
• anti-wear (reduced wear rate)
• anti-seize (increase in ultimate load of setting friction surfaces)
Compatible with all motor oils, does not enter into chemical reactions with oils and additives, does not change the viscosity of oils.
The tribotechnical composition of NEODRIVE is not an oil additive.
Efficiency:
• Reduces friction and wear on rubbing surfaces
• Increases engine service life …………………… 2-3 times
• Increases the overhaul life ... 1,5-3 times
• Increases engine power ……………………… 15-18%
• Reduces fuel consumption ………………………………… 15-18%
• Increases and evens out compression in engine cylinders to rated values
• Restores the parameters of worn-out units and mechanisms without disassembling them
• Reduces exhaust gas toxicity by 70-80%
• Increases oil service life by 2-3 times
• Facilitates engine starting at low temperatures
• Eliminates wear during cold start
• Cleans the engine lubrication system of soot and tar deposits
• The cost of processing components and mechanisms is 2-3 times lower than the cost of repairs using conventional technologies
The sequence of application of the tribotechnical composition "ENGINE":
1. Warm up the engine to a working temperature of at least +50 g.
2. Stop the engine.
3. Pour the contents of the vial (50 ml) into the oil filler neck of the engine.
4. Let the engine idle for 5-10 minutes.
5. Make 5-7 relapses.
6. Stop the engine for 10 minutes.
7. Start the engine again and ensure a mileage of at least 50 km.
Note:
• If the oil is very dirty, treat the engine after changing the oil and oil filter.
• The engine can be treated both in old oil (if there is at least 1000 km of run before the next scheduled oil change), and during a scheduled oil change.
• Processing of the motor-vehicle engine with the ENGINE composition is carried out after each regular oil change.
Packaging:
50 ml bottle with cap and label.
Cardboard box with instructions for use.
Storage conditions: from - 20 to + 50 degrees.
Shelf life: 5 years. The date of manufacture is indicated on the label.
